活门型孔“化方为圆”算法

通过对航空发动机控制系统活门型孔的流量系数稳定性控制的方法进行研究,提出了一套能够将方形活门型孔转化为有规律排列组合小圆孔的算法,并通过实例验证了算法的正确性,同时转化误差小于0.7%,基本实现了工程意义上的等流量系数。该算法将加工工艺性差且计量精度低的方形活门型孔转化为有规律排列组合小圆孔,消除了方形型孔流量系数变化的影响,改变了活门型孔加工方法,减少了对人和环境的危害,提高了活门型孔的计量精度,减小了活门的液动力,具有极大的工程应用价值。 该算法可以实现将方形、梯形（含三角形）及其组合型孔等任意型孔的转化,具有工程上的普遍适用性。     

高温高速气流总焓接触测试法对比分析

发动机尾焰、燃烧加热、电弧加热器等高温高速气流总焓测量存在较大误差,采用结构优化的质量吸入水冷焓探针,标定后的驻点热流和驻点压力探针(Fay-Riddell公式法)对高温高速气流总焓进行了对比测试。结果表明:焓值为2.5~5 MJ/kg时,焓探针的测试误差约为3.38%,采用Fay-Riddell公式法获得焓值的误差约为3%。焓探针与Fay-Riddell公式法平均偏差约为4.65%。在地面模拟试验时采用两种测焓方法确定测试精度,对减小高温高速气流测焓误差,提高试验模拟精度具有积极的作用。     

基于PIV技术的单圆孔脉冲射流流场特征

对稳态射流及脉冲射流冲击靶板时的流场特性结构进行了探索和分析。采用高频粒子图像测速技术,在射流管口到冲击靶板间距为6倍管径的条件下,对稳态射流进口雷诺数为6 000的稳态射流及脉冲频率为20 Hz的脉冲射流进行了实验测量,得到了射流核心区、壁面射流区及滞止区内的速度分布。研究发现:①由于射流剪切作用的影响,脉冲射流核心区的最大轴向脉动速度为稳态射流的3倍。②滞止区内,由于射流的剪切作用和壁面的滞止作用,导致了脉冲射流轴向速度梯度最大为稳态射流的2倍,同时,滞止区内的最大脉动速度是稳态射流脉动速度的3倍。③脉冲射流对壁面的卷吸以及旋涡的产生和传播过程,破坏了壁面射流区稳定的速度边界层。相比稳态射流,脉冲射流的流场增加了湍流相干结构的含能并产生周期性的大尺度卷吸涡。     

“蚌式”进气道附面层扫除特性风洞试验

以某低、高速风洞为平台,设计搭建了“蚌式”进气道附面层扫除特性测量试验系统,进行了不同流量系数和来流马赫数下进气道鼓包表面附面层扫除特性的风洞试验,通过对试验数据的整理、计算和对比分析同型号的飞行试验结果,研究了“蚌式”进气道鼓包表面附面层扫除特性。研究结果表明:在相同的来流马赫数下,随着流量系数的增大,鼓包表面附面层的扫除能力逐渐减弱;在亚声速工况的绝大多数流量范围内,鼓包表面压力系数沿鼓包中心线对称分布、压力梯度变化明显,且在不同截面沿主流方向具有增大的特征,鼓包构型对附面层扫除效果较强;超声速工况下具有明显附面层扫除能力的流量范围明显小于亚声速工况,进气道唇口形成的弓形激波是影响鼓包表面不同位置压力梯度变化的主要因素,进而决定着附面层扫除特性。在接近来流马赫数18及以上飞行工况下,附面层的扫除能力减弱,附面层分离加强,进而会造成较大的进气压力损失和畸变。     

脉冲爆震燃烧室出口燃气能量分布特性

为了提高脉冲爆震燃烧室出口燃气能量转换效率,采用数值计算方法,研究了带气动阀和爆震增强结构的脉冲爆震燃烧室出口燃气能量分布特性,结果表明:脉冲爆震燃气的膨胀过程先后经历一次膨胀、二次膨胀和过度膨胀3个阶段,单个周期内二次膨胀阶段的时间和能量占比最大;燃烧室出口燃气压力势能、动能、内能和能流密度的分布主要受燃气压力的影响,且变化规律与燃气压力一致;一次膨胀阶段燃气增加的压力势能、动能、内能分别占单个周期的479%、259%、251%;二次膨胀阶段燃气增加的压力势能、动能、内能分别占单个周期的502%、576%、581%。     

射频介质阻挡放电改善NACA 0015翼型气动性能的实验

介质阻挡放电(DBD)均匀稳定、易于敷设,是机翼/翼型等离子体流动控制(PFC)中最常用的激励方式。射频介质阻挡放电激励频率高、放电功率大,且能在流场中产生明显的加热,应用潜力大。采用射频电源驱动DBD激励器产生等离子体,分析放电的体积力、热特性和诱导流场特性,开展了射频介质阻挡放电改善NACA 0015翼型气动性能的实验,研究了占空比、调制频率、载波频率和电源功率等参数对流动控制效果的影响规律。结果表明:射频等离子体激励的体积力效应随激励电压的增大而增加;射频等离子体激励产生的热量在诱导的流场中进行传导,加速流场;当来流速度为20m/s,Re=3.36×10~5时,在翼型前缘施加激励,使翼型临界失速迎角推迟1°,最大升力系数增大6.43%,且在过失速迎角下仍具有流动控制效果,使升力下降变缓;调制频率越大,控制效果越好;存在最佳占空比、载波频率和功率,占空比对流场控制效果的影响最显著,最佳占空比、载波频率和功率分别为20%,460kHz和50W。射频等离子体激励以体积力效应、热效应和诱导壁面射流改善失速流场,使得NACA0015翼型气动性能极大改善,流动分离得到有效控制。     

Advances in critical technologies for hypersonic and high-enthalpy wind tunnel

Hypersonic and high-enthalpy wind tunnels and their measurement techniques are the cornerstone of the hypersonic flight era that is a dream for human beings to fly faster, higher and further. The great progress has been achieved during the recent years and their critical technologies are still in an urgent need for further development. There are at least four kinds of hypersonic and high-enthalpy wind tunnels that are widely applied over the world and can be classified according to their operation modes. These wind tunnels are named as air-directly-heated hypersonic wind tunnel, light-gas-heated shock tunnel, free-piston-driven shock tunnel and detonation-driven shock tunnel, respectively. The critical technologies for developing the wind tunnels are introduced in this paper, and their merits and weakness are discussed based on wind tunnel performance evaluation. Measurement techniques especially developed for high-enthalpy flows are a part of the hypersonic wind tunnel technology because the flow is a chemically reacting gas motion and its diagnosis needs specially designed instruments. Three kinds of the measurement techniques considered to be of primary importance are introduced here, including the heat flux sensor, the aerodynamic balance, and optical diagnosis techniques. The techniques are developed usually for conventional wind tunnels, but further improved for hypersonic and high-enthalpy tunnels. The hypersonic ground test facilities have provided us with most of valuable experimental data on high-enthalpy flows and will play a more important role in hypersonic research area in the future. Therefore, several prospects for developing hypersonic and high-enthalpy wind tunnels are presented from our point of view.     

Sensitivity analysis of flowfield modeling parameters upon the flow structure and aerodynamics of an opposing jet over a hypersonic blunt body

Implementation of an opposing jet in design of a hypersonic blunt body significantly modifies the external flowfield and yields a considerable reduction in the aerodynamic drag. This study aims to investigate the effects of flowfield modeling parameters of injection and freestream on the flow structure and aerodynamics of a blunt body with an opposing jet in hypersonic flow. Reynolds-Averaged Navier-Stokes (RANS) equations with a Shear Stress Transport (SST) turbulence model are employed to simulate the intricate jet flow interaction. Through utilizing a Non-Intrusive Polynomial Chaos (NIPC) method to construct surrogates, a functional relation is established between input modeling parameters and output flowfield and aerodynamic quantities in concern. Sobol indices in sensitivity analysis are introduced to represent the relative contribution of each parameter. It is found that variations in modeling parameters produce large variations in the flow structure and aerodynamics. The jet-to-freestream total-pressure ratio, jet Mach number, and freestream Mach number are the major contributors to variation in surface pressure, demonstrating an evident location-dependent behavior. The penetration length of injection, reattachment angle of the shear layer, and aerodynamic drag are also most sensitive to the three crucial parameters above. In comparison, the contributions of freestream temperature, freestream density, and jet total temperature are nearly negligible.     

扫频式射流对涡轮叶栅间隙泄漏流动影响的数值研究

为控制涡轮叶栅中叶顶间隙泄漏流动和改善涡轮气动性能,将扫频式射流器(SJA)作为一种主动流动控制方法应用在涡轮叶栅的研究中。通过非定常数值计算,分析了SJA对涡轮叶栅叶顶间隙流动的作用过程以及作用机理,并且研究了不同工况下SJA对涡轮叶顶流场改善效果以及不同频率的SJA对叶顶流场的影响。结果表明:通过在涡轮叶栅上端壁增加单个SJA装置,可以有效地延迟上端壁的流动分离,其中最佳方案射流流量仅为进口总流量的0.35%,涡轮叶栅出口截面总压损失系数减少了11.48%。存在着最佳的频率284Hz,使SJA装置对流场的作用效果最佳,有效地改善了涡轮叶栅内的间隙流动。     

端壁抽吸对压气机叶栅间隙泄漏流控制策略的研究

为了研究压气机机匣端壁抽吸对间隙泄漏流动控制的可行性和有效性,以高负荷压气机叶栅为研究对象,通过数值模拟方法对不同抽吸位置和抽吸流量率控制参数下的计算工况进行了对比和分析。研究结果表明:端壁抽吸可以直接地影响叶尖泄漏流的结构形态和存在形式,减弱叶尖泄漏流的强度和影响范围,进而提升压气机叶栅的性能;当抽吸槽覆盖范围包含叶尖泄漏流形成位置及稍靠后附近区域时,所对应的抽吸方案具有较好的控制效果,在0°攻角和0.5%的抽吸流量条件下前槽抽吸和中槽抽吸分别可获得7.04%和7.76%的叶栅总压损失增益;并且进一步研究发现端壁抽吸流量率存在上临界值,应针对不同攻角工况,在其相应的临界值范围内选择合理的抽吸流量,以达到用较小的吸气量实现对间隙泄漏流的控制。